用汇编语言实现RESET启动和热启动 程序名: RESET.ASM/BOOT.ASM 程序类别: 完整的汇编语言程序 功能: 用程序完成RESET启动和热启动 使用说明: 汇编连接以后转换为com文件运行 程序说明: 在日常用机过程中,如果出现了异常情况常常需要重新启动系统 .对于IBM PC 以及其兼容机,除了开机冷启动外,还有热启动和R ESET开关复位启动,他们的共同特点是转入BIOS的入口点(即ROM 的起始单元FFFF:0处),执行该处的跳转指令,转向启动程序,该启 动程序在执行过程中需检测复位标志字(在地址0040:0072处,占2 个字节)的值,若为1234则启动是不检测内存 若非1234则启动先检 测内存,再启动系统.热启动和RESET启动的不同之处在于热启动时 不检测内存,而RESET启动是需要检测内存. - 下载
|
本串行通信程序利用汇编语言通过BIOS中断调用和DOS功能调用实现PC机双机串行通信。其中，上位机和下位机串行口均为辅串口COM2（口地址为2FXH），对外用9针连接器与令一台PC机连接；BIOS通过“INT 14H”4个中断服务子程序，分别完成串口初始化编程、发送一帧数据、接受一帧数据以及测试通信线状态。本程序分为PC机串口自动测试程序（目的是测试串口好坏）和PC机全双工双机通信程序两个部分。-the serial communications procedures through the use of assembly language BIOS interrupt calls and function calls DOS PC Dual Serial Communication. Among them, PC and the next crew will be supplemented by serial port Serial COM2 (I address 2FXH) external with 9-pin connectors and enable a PC connection; through the BIOS "INT 14H," four interrupt service routines, complete serial port initialization programming, Send a data receiving a data communications test and the state line. The procedures are divided into PC serial automatic test procedure (for the purpose of testing Serial good or bad) and full-duplex PC-machine communication program two parts. 下载
|
本串行通信程序利用汇编语言通过BIOS中断调用和DOS功能调用实现PC机双机串行通信。其中，上位机和下位机串行口均为辅串口COM2（口地址为2FXH），对外用9针连接器与令一台PC机连接；BIOS通过“INT 14H”4个中断服务子程序，分别完成串口初始化编程、发送一帧数据、接受一帧数据以及测试通信线状态。本程序分为PC机串口自动测试程序（目的是测试串口好坏）和PC机全双工双机通信程序两个部分。 -the serial communications procedures through the use of assembly language BIOS interrupt calls and function calls DOS PC Dual Serial Communication. Among them, PC and the next crew will be supplemented by serial port Serial COM2 (I address 2FXH) external with 9-pin connectors and enable a PC connection; through the BIOS "INT 14H," four interrupt service routines, complete serial port initialization programming, Send a data receiving a data communications test and the state line. The procedures are divided into PC serial automatic test procedure (for the purpose of testing Serial good or bad) and full-duplex PC-machine communication program two parts. 下载
|
Lock Manage 是一个功能比较全面的加密软件。 它具有多种加密方案：如文件口令加密，文件反拷贝加密，软硬盘加密，安装加密，文本加密，批处理加密等等。系统是由Ｃ和汇编写成，可从外部链接于主模块。可单独编译，单独调试。可执行ＥＸＥ／ＣＯＭ程序加密模块已经过长时间的测试分析，其工作性能己十分稳定。可移植性与兼容性很好。另外，代码实现了ＣＳ，ＤＳ不换技术，使其ＳＨＥＬＬ性能难以被ＤＥＢＵＧ识别。其内部密码采用单向不可逆变换，基本实现了不可解，原因在于四个随机密钥只能用穷举法找出。这种可靠原四密钥单向加密技术渗透到了后面的几个程序中。对于反拷贝加密，采用了随机的软指纹生成技术，可生成唯一密钥母盘。硬盘反拷贝在硬盘里产生四密钥，在非母机上程序运行错误。反反汇编可将整个文件的内容加密变换。反跟踪采用了目前十余种通用的反跟踪算法。可抵抗ＤＥＢＵＧ系列软件。批处理和文本加密十分方便，但保密性不太强，只能用于一般用户。-Lock function is a more comprehensive encryption software. It has a wide variety of encryption programs : documents such as password encryption, anti-copy document encryption, hard disk encryption software, the installation of encryption, encrypted text, etc. batch encryption. C system is written and compiled, from the external links in the main module. Separately compiler, debugger alone. EXE executable / COM procedures encryption module has been tested over a long period of analysis, their performance has very stable. Good portability and compatibility. In addition, the implementation of the code of CS, DS is not for technology, it was difficult SHELL performance DEBUG identification. Its internal one-password irreversible transformation and the basic realization of Unsolvable because on 下载
|