单片机C51串口中断接收和发送测试例程,一个小的测试程序-80C51 Serial interrupted receive and send test routines, a small test procedures 下载
|
这是一个C51写的程序,采用Keil C51 编译开发.本程序是一个标准的串口收发程序.-This is a C51 written procedures, using Keil C51 compiler development. The procedure is a standard serial port transceiver procedures. 下载
|
单片机C51串口中断接收和发送测试例程可以用来测试51单片机的中断接收 //和查询发送，另外我觉得发送没有必要用中断，因为程序的开销是一样的 -80C51 Serial interrupted receive and send test routines can be used to test 51 MCU interrupt reception / / Send inquiries and, I also think that this is not necessary for discontinued because the process is the same as the overhead 下载
|
单片机C51串口接收（中断）和发送例程，可以用来测试51单片机的中断接收 -80C51 Serial reception (suspended) and send routines can be used to test 51 SCM interrupt reception 下载
|
Keil C51开发的一个单片机串口通信的源代码，包括发送和接收字符-Keil C51 microcontroller development of a serial communication source code, including the transmission and reception of characters 下载
|
c51用串口通信源码,包括调试 1.发送：向总线上发命令 2.接收：从总线接收命令，并分析是地址还是数据。 3.定时发送：从内存中取数并向主机发送.-decoder serial communication with the source code, including a debugger. Send : Bus made to order two. Acceptance : Bus from receiving orders and analysis of data or address. 3. Timing this : from memory a few sent to the mainframe. 下载
|
c51程序集锦，很好的源码，包括资料，其中包含：16进制<->10进制互换程序，24c01-24c16读写驱动程序，通用93c06-93c86系列，ACM-12864汉字液晶显示驱动程序，at29c040_card（有原理图），智能化家电控制，E-1330点阵液晶屏驱动程序，hd44780，HT1380实时时钟驱动程序，ht9200b驱动程序，单个汉字库字摸提取程序，tc2.0编译（源码），按键扫描驱动程序，串行驱动led显示，89C51系列CPU编程器（80F51,87F51），115.2k串行口通信程序，利用复位键作为开关机用，P89CXX编程器控制CPU接收和控制程序，软件红外线接收程序，P89CXX 编程器电脑发送程序，等等。里面还有不少电路图。- 下载
|
这是Small RTOS 51 在DP－51下载仿真实验仪上使用CAT24WC02驱动程序的例子。本例程序按照相应的的通讯协议接收一个数据，并将接收到的数据显示到LED数码显示器上。然后将接收到的数据写入Cat24Wc02中，再在同一位置将数据读出，并将读出的数据通过串口发送回来。通讯协议参考rtos随想曲和test.ini。 注意:(1)在KEIL C51 工程中,我已经把输出文件目录设在e:\temp中,您可以在Project->Options for Target "Target 1"的output页点击Select Folder for Objects...和Listing页点击Select Folder for Listing...改变. (2)编译时会有4个警告,可以忽略. (3)DP－51下载仿真实验仪的所有跳线选取默认值。-This is the Small RTOS 51 DP-51 download simulation NG use CAT24WC 02 Driver for example. The cases in accordance with the relevant procedures of receiving a communication protocol data and receiving the data shows that the LED digital display. Then sending the data into Cat24Wc02, again in the same position will be read out data, will be read out through the serial data sent back. Communication protocol reference rtos test.ini and Capriccio. Note : (1) in KEIL C51 project, I have incorporated the output directory in e : \ temp. You can Project - 下载
|
STC89C58软件实现SPI口做主机,STC12C4052的SPI口设为从机.实现双CPU通信.由主机从SPI口发送0x55,从机SPI口接收到数据后+10=0x5f,从SPI口发送回主机.主机接收后发到串口.串口助手观察接收数据．程度通过keil c51调试并下载到ＳＴＣ晶片运行．- 下载
|